If CS300/CS200/F11/F7/F6/RS200 Data Transfer Does not Work
In case SonicLink data transfer does not succeed, check that
- the training computer makes chirping noises when transferring data.
- your microphone is able to record audio to your computer (use e.g. Microsoft Sound Recorder to test).
Try also to adjust the microphone sound level.
1. Go to
Windows XP: Start → Settings → Control Panel → Sounds and audio devices → Audio → Sound recording and select Volume.
Windows Vista/7: Start → Control Panel → Sound → Recording → select the device in use → press Properties → select Levels tab and adjust the level.
Try to transfer the data again.
2. If the data transfer does not succeed, in Windows XP select Advanced.
3. Test if enabling/disabling microphone boost Advanced Controls for Microphone would give the desired result.
- If the microphone and loudspeaker are close to each other this can create a feedback loop. To prevent the loop turn off the computer's loudspeakers. For example, click the loudspeaker icon in the Windows taskbar and select Mute.
If you cannot find the loudspeaker icon in the taskbar, open the volume controller from the Windows Control Panel.
- Background noise or loud sounds (e.g. music, speaking or a phone ringing) may cause interference with SonicLink data transmission. Eliminate the noise and try the transmission again.
- If the microphone is selected as a playback device it may interfere with SonicLink transmission. Check that the microphone is not selected as a playback media in Control Panel → Sounds and Audio Devices/Sound. If disabling the microphone as playback media does not help, mute all playback devices and try the transmission again.
- The internal infrared port (only on laptops) may interfere with SonicLink with its regular checking for IR data availability. You can disable the internal infrared port in the Device Manager to block the IR port checking. Alternatively, you can try to extend the time delay for IR port checking to allow SonicLink transmission to finish.
4. In the WebLink software, try with SonicLink Low Volume.
Try with different distances. Distance between microphone and Polar product can vary from 0,5 cm up to 15 cm.
If the microphone is working and no other application (e.g. iTunes) is reserving it and/or sound card, the data transfer problem might stem from the sound card itself.
SoundMAX or Sound Card Using the Same ChipsetPlease check if you have a SoundMAX or card which uses the same chipset.
This can be seen from the icon at the system tray: / or from Start → Programs/Control Panel → SoundMAX or other sound card
If you have SoundMAX (usually integrated sound card, and it has the following icon at the system tray: .
Change the settings as follows:
1) In Windows XP open SoundMax Control Panel (right click the icon from the system tray and the pop-up menu is shown):
In Windows 7 open SoundMAX Audio Settings
2) In Windows XP remove "Noise reduction" or "Noise Suppression" selection and select "Headset" or "Standard Microphone" depending on the microphone you are using in microphone setup.
In Windows 7 select Recording Experience and adjust audio quality. Press Continue to calibrate your microphone.
Realtek Sound Card
If you have Realtek sound card, you can see the following icon at the systray:
Alternatively, select Start → Settings → Control Panel → Realtek.
Remove the "Noise Suppression" and "Acoustic Echo Cancellation" selections in FrontMic → Microphone Effects.
Adjust the Recording Volume.
In Default Format -tab, check that 16Bits, 44100 Hz (CD Quality) is selected.
If the data transfer problem persists, please contact your local helpdesk or global helpdesk for further help. To speed up the problem solving, copy the log file from your Polar WebLink software. You will find the log-file if you go to 'Log' in the lower left corner of the WebLink-window. Mark the text there, copy it and paste it to your message. If possible include information on your
- microphone type
- operating system
- Flash version
- speed of the internet connection